Civil Engineering Association

Design of Structural Reinforced Concrete Elements in Accordance with the Strength Design Method of AC1 318-95.

Design Examples On -
Base on ACI 99 with many example solved problem..

1. Flexure
2. Reinforcement
3. Shear
4. Footing
5. Deflection
6. Column
7. Two-way Slab
8. Seismic

PDF File ll 505 Pages





link contributed by vinnunsam

link contributed by Grunf

Title
Design Handbook: Beams, One-Way Slabs, Brackets, Footings, Pile Caps, Columns, Two-Way Slabs, and Seismic Design

American Concrete Institute

Publication Date:
Jan 1, 1997

Scope:


The ACI Design Handbook is intended for use by persons having a general familiarity with the strength design method and with “Building Code Requirements for Structural Concrete (ACI 3 18-95).”

This volume presents information for the engineering design and analysis of beams, slabs, brackets, footings, pile caps, columns, two-way slabs, and seismic design.

SECTIONS

Design Aids are tables and graphs intended to save the designer the effort of repeatedly performing routine calculations. All Design Aids apply to concrete having ƒ'a ranging between 3 and 12 ksi with Grade 40,60, and 75 steel reinforcement depending on the type of the structural member. A note at the bottom of each Design Aid indicates which Design Example illustrates the use of the table or graph.

Design Examples illustrate the use of the Design Aids (but are not intendeil to show how to design a structure).

Commentary on Design Aids gives the basis for the Design Aids. For judicious application and optimum efficiency, users of this handbook should first acquaint themselves with the Commentary. Design Examples will help verify procedures and results. It is not, however, the objective of the handbook to teach the novice how to design in reinforced concrete. Readers are expected to be competent in design before attempting to use this handbook.

(03-22-2009, 12:23 AM)robertsas Wrote: [ -> ]Base on ACI 99 with many example solved problem..

Code:

***************************************
Content of this section is hidden, You must be registered and activate your account to see this content. See this link to read how you can remove this limitation:

http://forum.civilea.com/thread-27464.html
***************************************

Try this link :



regards,
robertsasmita

ACI SP-17(09) ACI Design Handbook
Design of Structural Reinforced Concrete Elements in Accordance with ACI 318-05

Abstract: This publication provides information for the engineering design and analysis of beams, one-way slabs, footings, pile caps, columns, and seismic design in accordance with ACI 318-05. Information is presented in three sections: Explanatory Material, Design Examples, and Design Aids. The Introduction of each chapter includes explanatory material that provides the engineer with concise background of the subject. The Design Examples illustrate the use of the Design Aids, which are tables and graphs intended to eliminate routine and repetitious calculations.

Contents: Chapter 1—Design for flexure, p. 3

1.1—Introduction
1.2—Nominal and design flexural strengths (Mn and φMn)
1.3—Minimum flexural reinforcement
1.4—Placement of reinforcement in sections
1.5—Flexure examples
1.6—Flexure design aids

Chapter 2—Design for shear, p. 29

2.1—Introduction
2.2—Shear strength of beams
2.3—Designing shear reinforcement for beams
2.4—Shear strength of two-way slabs
2.5—Shear strength with torsion and flexure
2.6—Shear design examples
2.7—Shear design aids

Chapter 3—Short column design, p. 59

3.1—Introduction
3.2—Column sectional strength
3.3—Columns subjected to biaxial bending
3.4—Column examples
3.5—Column design aids

Chapter 4—Design of slender columns, p. 167

4.1—Introduction
4.2—Slenderness ratio
4.3—Lateral bracing and designation of frames as non-sway
4.4—Design of slender columns
4.5—Slender column examples
4.6—Slender column design aids

Chapter 5—Footing design, p. 189

5.1—Introduction
5.2—Foundation types
5.3—Allowable stress design and strength design
5.4—Structural design
5.5—Footings subject to eccentric loading
5.6—Footings examples

Chapter 6—Seismic design, p. 205

6.1—Introduction
6.2—Limitations on materials
6.3—Flexural members of special moment frames
6.4—Special moment frame members subjected to bending and axial load
6.5—Joints of special moment frames
6.6—Members of intermediate moment frames
6.7—Members not designed as part of the lateral-force-resisting system
6.8—Seismic design examples
6.9—Seismic design aids

Chapter 7—References, p. 229

7.1—Referenced standards and reports
7.2—Cited references

Appendix A—Reference tables, p. 231
Appendix B—Analysis tables, p. 237
Appendix C—Sectional properties, p. 251

New Link:

contents of the RAR file:

CHAPTER 1 - FLEXURE - SP-17 - 09-07
Chapter 2 - SHEAR DESIGN SP 17 - 09-07
Chapter 3 SP17 - 09-07
CHAPTER 4 - SLENDER COLUMNS - SP17 - 09-07
CHAPTER 5 - FOOTINGS - SP17 - 9-07
SEISMIC DESIGN - Chapter 6

---

Uploaded: Dec/29/2010, File Size: 4.9 MB, RAR'd 6 PDFs (paginated, search-able text)


If you like this publication, CivilEA's Team strongly suggest you to buy it! Support the authors!

There is an errata to this publication. I am not sure if it applies to this specific version. Anyway, you can download it there






mod: this is not link to the errata of the above document but aci search engine for their document errata.