FIB 16: Design examples for the 1996 FIP recommendations

Mohammad6299 · (This post was last modified: 03-28-2014, 07:58 PM by Mohammad6299.)

FIB 16: Design examples for the 1996 FIP recommendations Practical design of structural concrete

The 1996 FIP Recommendations Practical Design of Structural Concrete were finally published by SETO in September 1999. They had been developed based on the 1990 CEB-FIP Model Code.

The main objective of this Bulletin is now to demonstrate by practical examples the application of these recommendations, and especially to illustrate the use of strut-and-tie models for designing discontinuity regions in concrete structures. These examples represent also a continuation of the 1990 FIP Handbook on Practical Design that had been based on the former (1984) version of the recommendations. Most of the examples are recently built existing structures. Although some of them may be considered as quite important, the chosen examples are by no means exceptional.

The technical report does not deal with the discussion of aesthetic or general conceptual aspects. On the contrary, the main aim is to treat particular design aspects by selecting local regions of the chosen structures, that are then designed and detailed following the design principles and specifications proposed in the 1996 FIP Recommendations mentioned above.

Code:
***************************************

Content of this section is hidden, You must be registered and activate your account to see this content. See this link to read how you can remove this limitation:

http://forum.civilea.com/thread-27464.html

***************************************

Code:
***************************************

Content of this section is hidden, You must be registered and activate your account to see this content. See this link to read how you can remove this limitation:

http://forum.civilea.com/thread-27464.html

***************************************

Code:
***************************************

Content of this section is hidden, You must be registered and activate your account to see this content. See this link to read how you can remove this limitation:

http://forum.civilea.com/thread-27464.html

***************************************

This post has been made by CivilEA Post-Generator v2.2.0

arshiakh · 03-28-2014, 07:54 PM

FIB 16: Design examples for the 1996 FIP recommendations Practical design of structural concrete

The 1996 FIP Recommendations Practical Design of Structural Concrete were finally published by SETO in September 1999. They had been developed based on the 1990 CEB-FIP Model Code.

The main objective of this Bulletin is now to demonstrate by practical examples the application of these recommendations, and especially to illustrate the use of strut-and-tie models for designing discontinuity regions in concrete structures. These examples represent also a continuation of the 1990 FIP Handbook on Practical Design that had been based on the former (1984) version of the recommendations. Most of the examples are recently built existing structures. Although some of them may be considered as quite important, the chosen examples are by no means exceptional.

The technical report does not deal with the discussion of aesthetic or general conceptual aspects. On the contrary, the main aim is to treat particular design aspects by selecting local regions of the chosen structures, that are then designed and detailed following the design principles and specifications proposed in the 1996 FIP Recommendations mentioned above.

Code:
***************************************

Content of this section is hidden, You must be registered and activate your account to see this content. See this link to read how you can remove this limitation:

http://forum.civilea.com/thread-27464.html

***************************************

This post has been made by CivilEA Post-Generator v2.2.0

arshiakh · 03-28-2014, 08:56 PM

***************************************

Content of this section is hidden, You must be registered and activate your account to see this content. See this link to read how you can remove this limitation:

http://forum.civilea.com/thread-27464.html

***************************************

junaid · 03-29-2014, 08:18 AM

***************************************

Content of this section is hidden, You must be registered and activate your account to see this content. See this link to read how you can remove this limitation:

http://forum.civilea.com/thread-27464.html

***************************************

Possibly Related Threads…
Thread		Author	Replies	Views	Last Post
	ACI Mix Design w/ Examples	verongskey	2	1,778	12-17-2022, 12:05 PM Last Post: Dell_Brett
	Worked Examples for the Design of Concrete Structures to Eurocode 2	Mohammad6299	5	2,704	10-10-2017, 01:52 PM Last Post: lisine
	Examples of the Design of Reinforced Concrete Buildings to BS8110	babak	7	6,892	05-23-2016, 12:13 PM Last Post: Dobblo
	Reinforced Concrete: Design theory and examples	ibg0203	0	915	10-23-2015, 03:00 PM Last Post: ibg0203
	FIB 61: Design examples for strut-and-tie models	gonzo1982	3	2,736	09-24-2014, 08:33 AM Last Post: Dell_Brett
	Worked Examples For The Design of Concrete Buildings	aslam	8	5,570	07-12-2012, 05:13 AM Last Post: shadabg