SCI: Steel Building Design Guide Documents

[samjenkins]

SCI Steel Building Design Guide Documents

The latest (2010) documents produced by the SCI according to EC3 for steel construction

Code:

Content of this section is hidden, You must be registered and upgrade your account to see this content.

🔽🔽🔽🔽🔽🔽🔽🔽🔽
See this link to read how you can remove this limitation:
👉 CLICK HERE 👈

[metalgun]

direct link from CORUS CONSTRUCTION WEBSITE:

Code:

Content of this section is hidden, You must be registered and upgrade your account to see this content.

🔽🔽🔽🔽🔽🔽🔽🔽🔽
See this link to read how you can remove this limitation:
👉 CLICK HERE 👈

cheers!

[jorgeramos]

This publication presents design data derived in accordance with the following Parts of Eurocode 3
and their National Annexes
* BS EN 1993-1-1:2005: Design of steel structures. Part 1-1: General rules and rules for buildings.
* BS EN 1993-1-5:2006: Design of steel structures. Part 1-5: Plated structural elements.
* BS EN 1993-1-8:2005: Design of steel structures. Part 1-8: Design of joints.
Where these Parts do not give all the necessary expressions for the evaluation of data, reference is made to other published sources.
The resistances in this publication have been calculated using the partial factors for resistance given in the UK National Annexes for the Eurocode (NA to BS EN 1993-1-1:2005 as published in December 2008, NA to BS EN 1993-1-5:2006 as published in May 2008 and NA to BS EN 1993-1-8:2005 as published in November 2008). The partial factors are listed in Section 5.1. The other
parameters given in the National Annex that have been used when calculating member resistances are given in the relevant section of this publication.
The following structural sections are covered in this publication:
* Universal beams, universal columns, joists, bearing piles, parallel flange channels and
structural tees cut from universal beams and universal columns to BS 4-1
* Universal beams and universal columns produced by Corus but not included in BS 4-1
* Asymmetric Slimflor® beams (ASB) produced by Corus
* Equal and unequal angles to BS EN 10056-1
* Hot-finished structural hollow sections to BS EN 10210-2
* Cold-formed structural hollow sections to BS EN 10219-2
Section ranges listed cover sections that are readily available at the time of printing. The preparation and editorial work for this Edition was carried out by Miss E Nunez Moreno and Mr E Yandzio, both of the SCI, with technical assistance from Mr A S Malik of the SCI and Mr C M King, formerly of the SCI. The project was coordinated by Mr D G Brown, also of the SCI.
The work leading to this publication has been jointly funded by Tata Steel Europe*, SCI and BCSA and their support is gratefully acknowledged.
*

Code:

Content of this section is hidden, You must be registered and upgrade your account to see this content.

🔽🔽🔽🔽🔽🔽🔽🔽🔽
See this link to read how you can remove this limitation:
👉 CLICK HERE 👈

Code:

Content of this section is hidden, You must be registered and upgrade your account to see this content.

🔽🔽🔽🔽🔽🔽🔽🔽🔽
See this link to read how you can remove this limitation:
👉 CLICK HERE 👈

[apocalipse]

Dear member,

Someone please upload the book design data.

Thank you,
apocalipse

[andersen3]

@apocalipse - see here:

Code:

Content of this section is hidden, You must be registered and upgrade your account to see this content.

🔽🔽🔽🔽🔽🔽🔽🔽🔽
See this link to read how you can remove this limitation:
👉 CLICK HERE 👈