RAM Concept V8i 5.0.1 SELECTSeries 7 - Printable Version +- Civil Engineering Association (https://forum.civilea.com) +-- Forum: Software (https://forum.civilea.com/forum-65.html) +--- Forum: Software Product (https://forum.civilea.com/forum-105.html) +---- Forum: Bentley Products (https://forum.civilea.com/forum-42.html) +---- Thread: RAM Concept V8i 5.0.1 SELECTSeries 7 (/thread-40515.html) |
RAM Concept V8i 5.0.1 SELECTSeries 7 - BennyP - 12-22-2012 RAM Concept V8i 5.0.1 SELECTSeries 7 Size: 148.26 MB
Version: 05.00.01.04 Date: 10/12/2012 RAM Concept is an analysis and design program that uses the finite element method for elevated concrete floor systems, or mat foundations. The floors or mats can be post-tensioned concrete (PT), reinforced concrete (RC), or hybrid (a mixture of PT and RC). Concept is extremely powerful and allows you to design an entire floor in one model, or design individual strips or beams. In this context, the term “design” means that: • The user defines the following: structural geometry, loads, load combinations, and post-tensioning layout (if applicable). • Concept calculates (for any number of load combinations): the required amount of reinforcement for flexure and one-way shear according to relevant code requirements; the stud shear reinforcement (SSR) for punching shear, stresses for flexure, and deflections. Code: ***************************************
Private Note:
Code: *************************************** Code: *************************************** IMPORTANT NOTICE: You may use this software for evaluation purposes only. If you like it, it is strongly suggested you buy it to support the developers. By any means you may not use this software to make money or use it for commercial purpose. RE: RAM Concept V8i 5.0.1 SELECTSeries 7 - joker™ - 01-19-2013 Mirror RAM Concept V8i 5.0.1 SELECTSeries 7 - Size: 148.26 MB (Install File) Code: *************************************** RE: RAM Concept V8i 5.0.1 SELECTSeries 7 - joker™ - 01-19-2013 Mirror RAM Concept V8i 5.0.1 SELECTSeries 7 - Size: 148.26 MB (Install File) Code: *************************************** RE: RAM Concept V8i 5.0.1 SELECTSeries 7 - joker™ - 02-15-2013 RAM Concept V8i (Version: 05.00.02.12 Date: 2/12/2013 FileSize: 148.37 MB) Code: *************************************** RE: RAM Concept V8i 5.0.1 SELECTSeries 7 - bigone - 06-07-2014 RAM Concept V8i (Version: 05.01.01.10 Date: 2/4/2014 FileSize: 220.85 MB) Code: *************************************** Release Date: February 4, 2014 Installation Instructions: RAM Concept V8i Release 5.1.1 can be installed side-by-side with previous release versions of Concept. There is no need to uninstall previous release versions. Error Corrections in RAM Concept V8i Release 5.1.1 RAM Concept V8i Release 5.1.1 is a patch, containing error corrections and minor enhancements. Each issue addressed is summarized below. Audit Design Section When the user attempted to audit a cross section generated by a design section, an error with the message “Program Error (Report Parsing Error: bad master node contents)” resulted. Large Calc Log RAM Concept became unresponsive when the calc log had a large amount of output. DXF Import The import of a dxf file with missing xrefs into RAM Concept caused a program crash in specific and rare instances. ASCE 7-10 Wind Import When working with lateral loads that were imported from RAM Structural System, RAM Concept always treated wind loads as service loads, even when they might be ultimate level loads. Pre-Concept V8i Release 5.1 File Compatibility Warning: RAM Concept V8i Release 5.1 can read all previous file formats, but writes files in a format that cannot be read by previous versions. 32 bit Code: *************************************** Code: *************************************** Bentley.RAM.Concept.V8i.SS9.v05.02.00.21.x86.x64 - bigone - 09-17-2014 Bentley.RAM.Concept.V8i.SS9.v05.02.00.21.x86.x64 RAM Concept 5.2 Release Notes Code: *************************************** 32 bit Code: *************************************** 64bit Code: *************************************** LAVteam crack attached RE: RAM Concept V8i 5.0.1 SELECTSeries 7 - bigone - 04-25-2015 RAM Concept V8i v05.02.01.10 32 bit size 215.6 MB Code: *************************************** attached RE: RAM Concept V8i 5.0.1 SELECTSeries 7 - bigone - 04-25-2015 RAM Concept V8i v05.02.01.10 64 bit size: 237.0 MB Code: *************************************** Code: *************************************** RE: RAM Concept V8i 5.0.1 SELECTSeries 7 - joker™ - 06-25-2015 Bentley RAM Concept V8i SS9 05.02.01.10 build 02/04/2015 (x86 & x64) Size: 454.9 MB Code: *************************************** Code: *************************************** Code: *************************************** |