BS EN 10219:2006 Cold formed welded structural hollow sections of non-alloy and fine

BS EN 10219:2006 Cold formed welded structural hollow sections of non-alloy and fine - Printable Version

+- Civil Engineering Association (https://forum.civilea.com)
+-- Forum: eBooks (https://forum.civilea.com/forum-63.html)
+--- Forum: Codes, Manual & Handbook (https://forum.civilea.com/forum-16.html)
+---- Forum: British Standards (BS) (https://forum.civilea.com/forum-120.html)
+---- Thread: BS EN 10219:2006 Cold formed welded structural hollow sections of non-alloy and fine (/thread-22596.html)

BS EN 10219:2006 Cold formed welded structural hollow sections of non-alloy and fine - ir_71 - 02-28-2011

BS EN 10219 - 1:2006 Cold formed welded structural hollow sections of non-alloy and fine grain steels - Part 1: Technical delivery conditions

This part of this European Standard specifies the technical delivery conditions for cold formed welded structural hollow sections of circular, square or rectangular forms and applies to structural hollow sections formed cold without subsequent heat treatment. Requirements for tolerances, dimensions and sectional properties are contained in EN 10219-2.
NOTE A range of steel grades is specified in this European Standard and the user should select the grade appropriate to the intended use and service conditions. The grades and mechanical properties of the finished hollow sections are compatible with those in EN 10025-2 and EN 10025-3.

Code:
***************************************

Content of this section is hidden, You must be registered and activate your account to see this content. See this link to read how you can remove this limitation:

http://forum.civilea.com/thread-27464.html

***************************************

Made By CivilEA Post-Generator ver 2.0

BS EN 10219 - 2:2006 CCold formed welded structural hollow sections of non-alloy and fine grain steels — Part 2: Tolerances, dimensions and sectional properties

This part of EN 10219 specifies tolerances for cold formed welded circular, square and rectangular structural hollow sections, manufactured in wall thicknesses up to 40 mm, in the following size ranges:
Circular: Outside diameters up to 2 500 mm
Square: Outside dimensions up to 500 mm x 500 mm
Rectangular: Outside dimensions up to 500 mm x 300 mm
The formulae for calculating sectional properties of sections manufactured to the dimensional tolerances of this standard, to be used for the purposes of structural design, are given in Annex B. Dimensions and sectional properties for a limited range of sizes are given in Annex C. Technical delivery conditions are specified in EN 10219-1.
NOTE The designation of the sections' major axis (yy) and its minor axis (zz) align with the axis designation used for structural design in the structural Eurocodes.

Code:
***************************************

Content of this section is hidden, You must be registered and activate your account to see this content. See this link to read how you can remove this limitation:

http://forum.civilea.com/thread-27464.html

***************************************

Made By CivilEA Post-Generator ver 2.0

BS EN 10219:2006 - andersen3 - 10-05-2012

reposted; all links are dead

Code:
***************************************

Content of this section is hidden, You must be registered and activate your account to see this content. See this link to read how you can remove this limitation:

http://forum.civilea.com/thread-27464.html

***************************************

Code:
***************************************

Content of this section is hidden, You must be registered and activate your account to see this content. See this link to read how you can remove this limitation:

http://forum.civilea.com/thread-27464.html

***************************************

pass:

Code:
***************************************

Content of this section is hidden, You must be registered and activate your account to see this content. See this link to read how you can remove this limitation:

http://forum.civilea.com/thread-27464.html

***************************************

or DIN version only part1

Code:
***************************************

Content of this section is hidden, You must be registered and activate your account to see this content. See this link to read how you can remove this limitation:

http://forum.civilea.com/thread-27464.html

***************************************

RE: BS EN 10219:2006 Cold formed welded structural hollow sections - andersen3 - 11-18-2013

new links:

Code:
***************************************

Content of this section is hidden, You must be registered and activate your account to see this content. See this link to read how you can remove this limitation:

http://forum.civilea.com/thread-27464.html

***************************************

password:

Code:
***************************************

Content of this section is hidden, You must be registered and activate your account to see this content. See this link to read how you can remove this limitation:

http://forum.civilea.com/thread-27464.html

***************************************

RE: BS EN 10219:2006 - abualamal - 07-14-2015

Dear Friends

Below links for the files
BS EN 10219 - 1:2006

Code:
***************************************

Content of this section is hidden, You must be registered and activate your account to see this content. See this link to read how you can remove this limitation:

http://forum.civilea.com/thread-27464.html

***************************************

BS EN 10219 - 2:2006

Code:
***************************************

Content of this section is hidden, You must be registered and activate your account to see this content. See this link to read how you can remove this limitation:

http://forum.civilea.com/thread-27464.html

***************************************

Best Regards

RE: BS EN 10219:2006 Cold formed welded structural hollow sections of non-alloy and fine - concreteok - 06-03-2019

Code:
***************************************

Content of this section is hidden, You must be registered and activate your account to see this content. See this link to read how you can remove this limitation:

http://forum.civilea.com/thread-27464.html

***************************************