Civil Engineering Association

Full Version: AASHTO - Guide Specifications for LRFD Seismic Bridge Design
You're currently viewing a stripped down version of our content. View the full version with proper formatting.
AASHTO Guide Specifications for LRFD Seismic Bridge Design

Author: Roy A. Imbsen | Size: 16.19 MB | Format: PDF | Publisher: BSI | Year: 2007 | pages: 236

[Image: 83284730917953231446.jpg]


[Image: info.png]

The AASHTO Guide Specifications for LRFD Seismic Bridge Design is established in accordance with the NCHRP 20-07/Task 193 Task 6 Report. Task 6 contains five (5) Sections corresponding to Tasks 1 to 5 as follows:
SECTION 1 includes a review of the pertinent documents and information that were available.
SECTION 2 presents the justification for the 1000- year return period (which is approximately equivalent to a 7% probability of exceedance in 75 years) as
recommended for the seismic design of highway bridges.
SECTION 3 includes a description of how the “no analysis” zone is expanded and how this expansion is incorporated into the displacement based approach.
SECTION 4 describes the two alternative approaches available for the design of highway bridges with steel superstructures and concludes with a recommendation to use a force based approach for steel superstructures.
SECTION 5 describes the recommended procedure for liquefaction design to be used for highway bridges. This aspect of the design is influenced by the recommended design event and the no analysis zone covered in Tasks 2 and 3, respectively. The recommendations proposed are made taking into account the outcome of these two tasks for Seismic Design
Category D. The following recommendations are documented:
Task 2
1. Adopt the 7% in 75 years design event for development of a design spectrum.
2. Ensure sufficient conservatism (1.5 safety factor) for minimum support length requirement. This conservatism is needed to enable to use the reserve capacity of hinging mechanism of the bridge system. This conservatism shall be embedded in the specifications to address unseating vulnerability. At a minimum it is recommended to embed this safety factor for sites outside of California.
3. Partition Seismic Design Categories (SDC’s) into four categories and proceed with the development of analytical bounds using the 7% in 75 years design event.

[Image: Download.png]
Code:
***************************************
Content of this section is hidden, You must be registered and activate your account to see this content. See this link to read how you can remove this limitation:

http://forum.civilea.com/thread-27464.html
***************************************

AASHTO Guide Specifications for LRFD Seismic Bridge Design, 1st ed, 2009
Code:
***************************************
Content of this section is hidden, You must be registered and activate your account to see this content. See this link to read how you can remove this limitation:

http://forum.civilea.com/thread-27464.html
***************************************
AASHTO - Guide Specifications for LRFD Seismic Bridge Design, 2nd Edition, 2011
Code:
***************************************
Content of this section is hidden, You must be registered and activate your account to see this content. See this link to read how you can remove this limitation:

http://forum.civilea.com/thread-27464.html
***************************************
AASHTO Guide Specifications for LRFD Seismic Bridge Design (2nd Edition)

Author: AASHTO | Size: 4.8 MB | Format: PDF | Quality: Original preprint | Publisher: American Association of State Highway and Transportation Officials | Year: 2011 | pages: 266 | ISBN: 9781560515210

[Image: 56950690072860668976.jpg]


[Image: info.png]

Covers seismic design for typical bridge types and applies to non-critical and non-essential bridges. Approved as an alternate to the seismic provisions in the AASHTO LRFD Bridge Design Specifications. Differs from the current procedures in the LRFD Specifications in the use of displacement-based design procedures, instead of the traditional force-based R-Factor method. Includes detailed guidance and commentary on earthquake-resisting elements and systems, global design strategies, demand modeling, capacity calculation, and liquefaction effects. Capacity design procedures underpin the Guide Specifications' methodology; includes prescriptive detailing for plastic hinging regions and design requirements for capacity protection of those elements that should not experience damage.

[Image: download.png]
Code:
***************************************
Content of this section is hidden, You must be registered and activate your account to see this content. See this link to read how you can remove this limitation:

http://forum.civilea.com/thread-27464.html
***************************************


[Image: password.png]
Code:
***************************************
Content of this section is hidden, You must be registered and activate your account to see this content. See this link to read how you can remove this limitation:

http://forum.civilea.com/thread-27464.html
***************************************



AASHTO Guide Specifications for Seismic Bridge Design

Author: Roy A Imbsen; American Association of State Highway and Transportation Officials. Subcommittee on Bridges and Structures | Size: 4.7 MB | Format: PDF | Quality: Unspecified | Year: 2009 | pages: 266

[Image: 09653264071956939693.jpg]


[Image: info.png]




[Image: download.png]
Code:
***************************************
Content of this section is hidden, You must be registered and activate your account to see this content. See this link to read how you can remove this limitation:

http://forum.civilea.com/thread-27464.html
***************************************


Version 2007


***************************************
Content of this section is hidden, You must be registered and activate your account to see this content. See this link to read how you can remove this limitation:

http://forum.civilea.com/thread-27464.html
***************************************


Version 2009


***************************************
Content of this section is hidden, You must be registered and activate your account to see this content. See this link to read how you can remove this limitation:

http://forum.civilea.com/thread-27464.html
***************************************


Version 2011


***************************************
Content of this section is hidden, You must be registered and activate your account to see this content. See this link to read how you can remove this limitation:

http://forum.civilea.com/thread-27464.html
***************************************

AASHTO Guide Specifications for Seismic Bridge Design, 2ned edition

Author: AASHTO | Size: 4.17 MB | Format: PDF | Quality: Original Preprint | Year: 2011 | pages: 266 | ISBN: 9781560513964 , 1560513969

[Image: download.png]

Code:
***************************************
Content of this section is hidden, You must be registered and activate your account to see this content. See this link to read how you can remove this limitation:

http://forum.civilea.com/thread-27464.html
***************************************


[Image: password.png]

Code:
***************************************
Content of this section is hidden, You must be registered and activate your account to see this content. See this link to read how you can remove this limitation:

http://forum.civilea.com/thread-27464.html
***************************************