Perform3D v7

[joker™]

PERFORM-3D 7.0.0

Size: 123 MB

Traditionally, earthquake-resistant design has been strength-based, using linear elastic analysis. Since inelastic behavior is usually allowed for strong earthquakes, this is not entirely rational. Strength-based design considers inelastic behavior only implicitly. Displacement-based (or deformation-based) design considers inelastic behavior explicitly, using nonlinear inelastic analysis. Displacement-based design recognizes that in a strong earthquake, inelastic deformation (or ductility) can be more important than strength. PERFORM-3D allows you to use displacement-based design.

Procedures for displacement-based design using inelastic analysis are specified in ASCE 41, “Seismic Rehabilitation of Existing Buildings”. ASCE 41 applies to the retrofit of existing buildings, but the procedures can be applied to the design of new buildings. PERFORM-3D implements the procedures in ASCE 41. However, PERFORM-3D is a general tool for implementing displacement-based design. It is not limited to ASCE 41.

Private Note:

PERFORM-3D 7.0.0 Enhancements:

Code:

Content of this section is hidden, You must be registered and upgrade your account to see this content.

🔽🔽🔽🔽🔽🔽🔽🔽🔽
See this link to read how you can remove this limitation:
👉 CLICK HERE 👈

Code:

Content of this section is hidden, You must be registered and upgrade your account to see this content.

🔽🔽🔽🔽🔽🔽🔽🔽🔽
See this link to read how you can remove this limitation:
👉 CLICK HERE 👈

Code:

Content of this section is hidden, You must be registered and upgrade your account to see this content.

🔽🔽🔽🔽🔽🔽🔽🔽🔽
See this link to read how you can remove this limitation:
👉 CLICK HERE 👈

Code:

Content of this section is hidden, You must be registered and upgrade your account to see this content.

🔽🔽🔽🔽🔽🔽🔽🔽🔽
See this link to read how you can remove this limitation:
👉 CLICK HERE 👈

Code:

Content of this section is hidden, You must be registered and upgrade your account to see this content.

🔽🔽🔽🔽🔽🔽🔽🔽🔽
See this link to read how you can remove this limitation:
👉 CLICK HERE 👈

[zrilek]

kg only

Code:

Content of this section is hidden, You must be registered and upgrade your account to see this content.

🔽🔽🔽🔽🔽🔽🔽🔽🔽
See this link to read how you can remove this limitation:
👉 CLICK HERE 👈

Code:

Content of this section is hidden, You must be registered and upgrade your account to see this content.

🔽🔽🔽🔽🔽🔽🔽🔽🔽
See this link to read how you can remove this limitation:
👉 CLICK HERE 👈

Code:

Content of this section is hidden, You must be registered and upgrade your account to see this content.

🔽🔽🔽🔽🔽🔽🔽🔽🔽
See this link to read how you can remove this limitation:
👉 CLICK HERE 👈

[maiii]

Dear All,
Crack is not working now.How to do?

[ESTRUCTO]

Dear All,
Crack is not working now.How to do?

Hi,

You could change the date in Windows, for example, you could use this: 02-01-18. It works for me.

Good luck!

[zipatton]

Hi,
you can as well use the software "Run As Date". It works fine for all products. Look for it around the net.
good  luck

Zippat

[faros3000]

Does anyone have an external link with the installation file? I can not access it in the CSI website.

[kowheng]

Setup file
[MIRROR]Content of this section is hidden, You must be registered and upgrade your account to see this content.
[/MIRROR] 🔽🔽🔽🔽🔽🔽🔽🔽🔽
See this link to read how you can remove this limitation:
👉 CLICK HERE 👈

Code:

Content of this section is hidden, You must be registered and upgrade your account to see this content.

🔽🔽🔽🔽🔽🔽🔽🔽🔽
See this link to read how you can remove this limitation:
👉 CLICK HERE 👈