Analysis of a Building 4 floors in Etabs

Analysis of a Building 4 floors in Etabs - Printable Version

+- Civil Engineering Association (https://forum.civilea.com)
+-- Forum: Civil Engineering Resource (https://forum.civilea.com/forum-1.html)
+--- Forum: Civil Engineering Documents (https://forum.civilea.com/forum-89.html)
+---- Forum: Calculation Notes & Analysis Files (https://forum.civilea.com/forum-80.html)
+---- Thread: Analysis of a Building 4 floors in Etabs (/thread-7171.html)

Analysis of a Building 4 floors in Etabs - Veggeta - 12-11-2009

Analysis of a building of metallic structure of 4 floors(flats), realized in Etabs...

[Image: screen.png]

Code:
***************************************

Content of this section is hidden, You must be registered and activate your account to see this content. See this link to read how you can remove this limitation:

http://forum.civilea.com/thread-27464.html

***************************************

Code:
***************************************

Content of this section is hidden, You must be registered and activate your account to see this content. See this link to read how you can remove this limitation:

http://forum.civilea.com/thread-27464.html

***************************************

RE: Analysis of a Building 4 floors in Etabs - Administrator - 12-11-2009

can you explain more from this model?

- type of frames
- codes of design
- place
- type of other elements
....

this look a good model...

RE: Analysis of a Building 4 floors in Etabs - robertsas - 12-11-2009

Dear Veggeta,

I run this model without change anything, it give :

* * * W A R N I N G * * *
ZERO STIFFNESS FOUND DURING SOLUTION FOR DOF UX OF JOINT 872
LOCATED AT X = 12.500000, Y = 1.500000, Z = 5.650000,
STIFFNESS MATRIX DIAGONAL VALUE SET TO 1.00E-10

* * * W A R N I N G * * *
THE STRUCTURE IS UNSTABLE OR ILL-CONDITIONED !!
CHECK THE STRUCTURE CAREFULLY FOR:
- INADEQUATE SUPPORT CONDITIONS, OR
- ONE OR MORE INTERNAL MECHANISMS, OR
- ZERO OR NEGATIVE STIFFNESS PROPERTIES, OR
- EXTREMELY LARGE STIFFNESS PROPERTIES, OR
- BUCKLING UNDER P-DELTA LOADS (IF ANY), OR
- AN EIGEN SHIFT (IF ANY) ONTO A NATURAL FREQUENCY

I fixed it because some of stair beams are not conected to the bordes (LOCATED AT X = 12.500000, Y = 1.500000, Z = 5.650000)

May I ask you what kind of material Durock? Can you explained what is that material..
because you run with UBC respons spectrum with Scale Factor = 0,3...

regards,
robertsasmita

RE: Analysis of a Building 4 floors in Etabs - vinnunsam - 12-11-2009

Dear Veggeta,

Have you prepared a DBR (Design Basis Report) for this model. If you have completed, can you upload it.

RE: Analysis of a Building 4 floors in Etabs - Veggeta - 12-11-2009

Dear Robertsas,
I will check the very prompt model, it is possible that I have been wrong of file ... what happens is that I am out for labour motives and not have access to my files these days..

If I have it, but in Spanish, I am going to summarize it and am going to hang it...

Sorry for the caused problems...

Sorry bad englis...

Regards...

RE: Analysis of a Building 4 floors in Etabs - Nilupa - 12-22-2009

don't you have sap analysis file..?

RE: Analysis of a Building 4 floors in Etabs - tase - 01-28-2010

hello!
If you still watch this thread can you explain me what was to purpose of modelling the exterior walls? The horizontal shear force will load these walls while the frames will be unloaded.