Civil Engineering Association
2d dam analysis - Printable Version

+- Civil Engineering Association (https://forum.civilea.com)
+-- Forum: Civil Engineering Resource (https://forum.civilea.com/forum-1.html)
+--- Forum: Civil Engineering Documents (https://forum.civilea.com/forum-89.html)
+---- Forum: Calculation Notes & Analysis Files (https://forum.civilea.com/forum-80.html)
+---- Thread: 2d dam analysis (/thread-7085.html)



2d dam analysis - preceptor - 12-07-2009

2D DAM ANALYSIS WITH SAP2000 V14

[Image: 91002081100427578107.jpg]

[Image: info.png]
Here
a linear analysis for 2d dam




[Image: Download.png]

Code:
***************************************
Content of this section is hidden, You must be registered and activate your account to see this content. See this link to read how you can remove this limitation:

http://forum.civilea.com/thread-27464.html
***************************************

[Image: password.png]

Code:
***************************************
Content of this section is hidden, You must be registered and activate your account to see this content. See this link to read how you can remove this limitation:

http://forum.civilea.com/thread-27464.html
***************************************



RE: 2d dam analysis - jloblitas - 12-07-2009

Hi:
Thanks for this file, is excellent.
Do you have any examples for a earth dam?
Thanks


RE: 2d dam analysis - robertsas - 12-08-2009

Dear Preceptor,

I think we should also modelize all FEM for soil with soil property and soil water to this dam (concrete structure).
Honestly, I never design a dam before..

regards,
robertsasmita


RE: 2d dam analysis - nhim4mat2006 - 12-08-2009

Foundation should be included as a solid region. Material properties of foundation should not include any mass (if included the foundation will be settle by it own weight, which is not true), but including deformation modulus and poisson ratio. The region should be at least 1H wide from upstream or downstream toe of the dam, and 1H down from the foundation contact (H is the dam height).


RE: 2d dam analysis - ynopum - 12-11-2009

If you are student you dont need to read the following, but if you have to perform calculation for real project let me give you the "cold shower".
For such type of dam (concrete gravity type) you HAVE TO pass through the following steps:

1. Foundation prior to the dam construction shall be modeled for proper stress estimation, especially in layered foundation (the foundation is usually the weaker part of all). That is because you will need the stresses to assess the safety factor, and weightless foundation makes the stresses there completely unreal (but the displacements are fine).

2. Stresses in the foundation should be kept, but the displacements set to zero.

3. Next stage is the dam construction (single stage or several stages, depending on what you want to obtain). After that displacements should be set to zero again in most cases.

4a. Seepage analysis through the foundation should be made, this giving the water pressure on the upstream face and the uplift pressure on the dam foundation; or
4b.If you can't do seepage analysis you must directly put the uplift pressure acting on both directions (perpendicular) to a thin contact layer between the rock and the dam body. This is not correct in respect to the foundation, so you should then limit your results only in the dam-body part, and forget any results in the rock - that means you can't do the following steps.

5. If you did 4a you can use effective stress plastic criteria (Coulomb-Mohr, Hoek-Brown) to check the foundation.

6. You can integrate normal and shear stresses on the dam-foundation contact, or several sliding planes passing through the foundation, or lift-joints in the dam body (for lift-joits you don't need foundation seepage) to obtain the sliding factor of safety.

7. Perform pseudo-static, response spectrum, or transient analysis for earthquake (MCE and OBE) and check the stresses and stability again.

I suspect that SAP2000 is not completely suited for staged construction with plastic material behavior.


RE: 2d dam analysis - vinnunsam - 12-11-2009

Dear preceptor,

Do you have an mirror link. This seems to be moved or deleted. I know its been more than 4 months. Does anybody has a mirror link.

[Image: 70096880893359854169.jpg]


RE: 2d dam analysis - preceptor - 12-13-2009

here a nwe link

Code:
***************************************
Content of this section is hidden, You must be registered and activate your account to see this content. See this link to read how you can remove this limitation:

http://forum.civilea.com/thread-27464.html
***************************************